This might be tangential to HomeAssistant but Im currently thinking about a household renovation and one thing I am considering is wiring.
I have some POE devices along with many other that run with a 12v DC supply.
I’m lookin at putting in a relatively straightforward 12v battery UPS with a small solar panel to charge. I probably only have space for 1500W of panels so putting in a whole grid tied solution is overkill. Primarily this is to provide backup as we sometimes lose power.
Networking wise I think I will put RJ45 into each room as we are concrete reinforced construction and so signal quality is an issue.
My query was how feasible it is to run both standard PEO devices and 12v devices (1-2w) all over POE.
I thought the alternative would be to run separate 12v cables with USB connectors at the end into each room as well as Rj45
On the input side of things one idea I had was if I was running 12v DC on a separate cable run to power that I could have a battery / solar panel providing an independent supply since our 230v AC is strung from poles and does trip in bad weather.
Using POE does complicate that slightly I would have to find injectors that I could take that input and then extractors for USB, RJ45 and 12VDC output.
On the positive side of thing it would mean I could really reduce the number of 230 VAC sockets I would be putting around the house with just kitchen and laundry needing them.
Im also considering doing lightning at 12V LED rather than 230V
I’m not sure I’m getting the gist of your questions, but as far as POE goes, if the device is designed to accept it, it will work at the negotiated PD voltage without problems, but you need a legit POE injector or switch.
If you’re saying there is some “other” 12V power you’re planning on running over different Cat6 cables, I don’t understand why you’d want to do that.
I was debating running Ethernet and a separate pair of cables for 12DC - Thinking maybe I might need thicker cables for USB-C levels of power and / having separate USB faceplates but looking again I think everything could run on Ethernet and then just decide / change what i put on the end.
Personally I’d run separate 12VDC cabling instead of pulling out from POE if it’s simple to do, but if you get a splitter which will negotiate POE (assuming you don’t run some older passive-POE setup) it should work just fine. But note, that POE goes up to 57VDC, so check that you can run your POE switch/injector with 12VDC at all.
Well you definitely don’t want to put the power cables in the same conduit with the data cables (PoE being the exception). Run two conduits (one for power, one for data) separated by the distance specified by your local electrical code (probably at least a foot or so, and wider is better). If the conduit is metallic, then the spacing can be less.
In those conduits, run:
The wires you actually know you need right now, and
Also remember that cables… are just cables. They will take whatever connector you put on thebend of it. So you can use a different one 12v so you dont accidentaly plug things in wrong.
But if you need to pull dc out of POE, you can get thigs that do just that. Search for POE extract or splitter. Many will let you pick wjat voltage to get out of it.
Imo youre better off running cat6 or 6a everywhere (better yet conduit where reasonable) and not running a 2 conductor pair along with your cat cable. Just terminate your cat cable as usb if you dont want to use an extractor.
You are not logged in. However you can subscribe from another Fediverse account, for example Lemmy or Mastodon. To do this, paste the following into the search field of your instance: !homeassistant@lemmy.world
Home Assistant is open source home automation that puts local control and privacy first. Powered by a worldwide community of tinkerers and DIY enthusiasts. Perfect to run on a Raspberry Pi or a local server. Available for free at home-assistant.io
So a bit more thinking on this.
Looking at https://community.fs.com/article/understanding-poe-standards-and-poe-wattage.html POE could probably do a lot more than a few watts and could t feels like I could use POE to provide power for most of my devices providing cabled connection and power in one.
On the input side of things one idea I had was if I was running 12v DC on a separate cable run to power that I could have a battery / solar panel providing an independent supply since our 230v AC is strung from poles and does trip in bad weather.
Using POE does complicate that slightly I would have to find injectors that I could take that input and then extractors for USB, RJ45 and 12VDC output.
On the positive side of thing it would mean I could really reduce the number of 230 VAC sockets I would be putting around the house with just kitchen and laundry needing them.
Im also considering doing lightning at 12V LED rather than 230V
I’m not sure I’m getting the gist of your questions, but as far as POE goes, if the device is designed to accept it, it will work at the negotiated PD voltage without problems, but you need a legit POE injector or switch.
If you’re saying there is some “other” 12V power you’re planning on running over different Cat6 cables, I don’t understand why you’d want to do that.
I was debating running Ethernet and a separate pair of cables for 12DC - Thinking maybe I might need thicker cables for USB-C levels of power and / having separate USB faceplates but looking again I think everything could run on Ethernet and then just decide / change what i put on the end.
Personally I’d run separate 12VDC cabling instead of pulling out from POE if it’s simple to do, but if you get a splitter which will negotiate POE (assuming you don’t run some older passive-POE setup) it should work just fine. But note, that POE goes up to 57VDC, so check that you can run your POE switch/injector with 12VDC at all.
Let me see if I’ve got the picture:
Obvious solution: run conduit.
Haha of course it s going to be conduit. But its what to put in it. Just 230v ac or add 12v dc or POE or both.
Well you definitely don’t want to put the power cables in the same conduit with the data cables (PoE being the exception). Run two conduits (one for power, one for data) separated by the distance specified by your local electrical code (probably at least a foot or so, and wider is better). If the conduit is metallic, then the spacing can be less.
In those conduits, run:
Yeah … Definitely will put conduits in .
Also remember that cables… are just cables. They will take whatever connector you put on thebend of it. So you can use a different one 12v so you dont accidentaly plug things in wrong.
But if you need to pull dc out of POE, you can get thigs that do just that. Search for POE extract or splitter. Many will let you pick wjat voltage to get out of it.
Imo youre better off running cat6 or 6a everywhere (better yet conduit where reasonable) and not running a 2 conductor pair along with your cat cable. Just terminate your cat cable as usb if you dont want to use an extractor.